TraceDraw 帮助
TraceDraw 帮助/线条、形状和轮廓/Dimension lines and callouts

此页面尚未翻译,以英文显示。

Dimension lines and callouts

Dimension lines show the size of things in a technical drawing: a length, a horizontal or vertical distance, an angle or the length of a segment. Callouts point at something with a leader line and a label. Both stay live: when you move, scale or turn them, they are measured and drawn again.

Placing a dimension

Every dimension is placed in clicks, and the property bar says what to click next. While the last point is wanted, the dimension follows the pointer. Esc starts again. Points snap as drawing does, so snapping to nodes or objects gives exact measures; see Snapping. The new dimension is selected.

Parallel

The Parallel Dimension tool measures the straight distance between two points, at any angle:

  1. Drag from the first point to the second, or click both.
  2. Move the pointer and click where the dimension line goes.

Horizontal or Vertical

The Horizontal or Vertical Dimension tool measures only the horizontal or the vertical distance between two points, whichever is larger. Place it as a parallel dimension.

Angular

The Angular Dimension tool measures an angle:

  1. Click the vertex of the angle.
  2. Click a point on the first side, then a point on the second side.
  3. Click where the arc goes.

The angle is measured counterclockwise from the first side.

Segment

The Segment Dimension tool measures a segment of an object: click the segment to take its two ends, then click where the dimension line goes.

Add dimensions to objects

Select objects and choose Object > Insert > Add Dimensions (it is also in the right-click menu): a dimension along the bottom measures the width of the selection's box, and one along the right its height, each 5 mm away from it, in the dimension style and units below. With Add Dimensions to Each Object, each selected object gets its own pair. Dimensions in the selection are not measured, and an object with no height (or width) gets no dimension for it. The new dimensions are selected and one undo takes them all away.

Sizes and areas

Tools > Sizes and Areas lists the sizes of the selected objects, each object's box width by height, with the objects of the same size counted together ([3x] 50.00 x 30.00 mm), how many objects and sizes there are, the total area of their boxes and the area the closed objects really cover (holes taken out), in square metres (and square feet with imperial units). Its Pages tab lists every page's size and the pages' total area. Sizes are in the document's unit, through the drawing scale for objects; pages are as printed. Copy puts the list on the clipboard as text, for a quote or an order, and Add Dimensions to Each Object labels each selected object with its width and height (see above).

Dimension style

The property bar shows these settings with the dimension tools and when the selection is all dimensions. Changes apply to the selected dimensions and to the next ones you make.

  • Precision: 0 to 6 decimals (2 at first).
  • Units: the drawing units (at first) or any other unit. Lengths follow the drawing scale, so at 1:100 a 10 mm line reads 1000 mm; see Document options.
  • Show units: the unit after the number (the degree sign for angles).
  • Prefix and Suffix: text before and after the number.
  • Text: above the line (at first), in the line, or below the line.
  • Place: where a linear dimension's label sits along its line: in the middle (at first), toward the start or the end, or outside the extension lines at either end, for a short dimension with no room for its label.
  • Label size: 1 to 500 points (10 at first).
  • Font of the label (the font of new text at first) and the label color (black).
  • Line color (black) and line width (a hairline at first, up to 50 mm), for the lines and arrowheads.
  • Arrowheads: arrow (at first), open arrow, dot, tick or none.
  • Round ends: round caps and joins on the lines (off).
  • The Options menu: the extension line gap between the measured points and the extension lines (0), how far the extension lines run past the line (2 mm), horizontal text for linear dimensions (off), join lines at corners (off), which makes the extension lines and the dimension line (or an angle's arc) one line that turns a corner instead of running past it, and a corner radius (0 to 100 mm) that rounds those corners. The menu stays open while you type in it.

The label always reads left to right and stays upright. Double-click it with the Pick tool to edit it in place: text that still holds the measured value keeps it live (the text before and after it become the prefix and suffix); text without it shows as typed until you delete it.

Dimensions that follow objects

A dimension whose ends you placed on an object holds to it: on its nodes (its corners, say), or on its edges (the sides of a rectangle, not only its corners). When you move, resize, turn or reshape the object, the dimension goes along, each end keeping its place on its node or along its edge, and the value changes with it. Moving the dimension by itself lets it go, as does deleting the object or the node it held to.

When you move, scale or turn a dimension, it is measured and drawn again: a dimension scaled by 2 reads twice the length, and its label stays upright.

Break Apart (Ctrl+K) frees the lines, arrowheads and label as objects of their own, and Convert to Curves (Ctrl+Q) makes the dimension a group of plain curves. Either way it is no longer a dimension.

Callout

The 3-Point Callout tool draws a label with a leader line in two segments.

  1. Drag from the tip (what the callout points at) to the elbow, or click both.
  2. Click where the text goes. The text goes on that side of the elbow.
  3. Type the text. The sample text is selected, so typing replaces it.

The leader always ends at the text: when you type more, change the size or move the text on its own (Ctrl+click it), the leader follows. Move the tip or the elbow with the Shape tool.

The property bar, shown with the tool and when the selection is all callouts, sets:

  • the outline width of the leader and shape (a hairline at first);
  • the line style;
  • the head at the tip (an arrow at first, or none);
  • the callout shape around the text: none (at first), underline, rectangle, rounded rectangle or ellipse;
  • the gap between the text and the leader or shape (1 mm at first).